Horizontal
Long cylinders and shells
The mould turns about a horizontal axis on rollers. Used for cylindrical decanter bowls, pipes, tubes, liners and suction roll shells, where length exceeds diameter.
01Technology
Centrifugal casting, sand casting and patternless 3D sand printing sit under one roof with melting, AOD refining, heat treatment, machining and testing. The route is chosen for the part, and the whole chain stays under one quality system.
1.1Centrifugal casting
Molten metal is poured into a spinning mould and held against the wall by centrifugal force until it solidifies. The method produces rotationally symmetric parts in one piece: bowls, shells, rings, pipes and sleeves.
Source: manufacturer’s published data. The manufacturer describes its horizontal and vertical centrifugal machines as the largest in China.
0× gravity at the mould wall
G = ω²r / g. A general physics illustration of why rotation densifies the wall. Actual casting parameters are set by the foundry for each alloy, diameter and wall section.
Horizontal
The mould turns about a horizontal axis on rollers. Used for cylindrical decanter bowls, pipes, tubes, liners and suction roll shells, where length exceeds diameter.
Vertical
The mould turns about a vertical axis. Used for conical bowls, end hubs, casings and rings, where the profile changes along the axis or the part is short.
1.2Sand casting
Where a part is not a body of revolution, it is poured in sand. The foundry concentrates on large, highly complex stainless steel castings: volutes, impellers, pulper rotors, valve bodies, turbine components and gratings.
Schematic. For integrated complex structures, moulds and cores are 3D sand-printed instead of being formed around a pattern.
1.3PCM 3D sand printing
Patternless Casting Manufacturing prints sand moulds and cores directly from digital data. The manufacturer was the first in China to combine it with stainless steel casting, and uses it for new product development, small series of many variants and structures a pattern could not release.
>30%
lower casting manufacturing cost
>50%
shorter production cycle
Route to the first casting
Cost and cycle reductions are the manufacturer’s published figures for PCM compared with conventional pattern-based sand casting. Route diagram is schematic and not to scale.
1.4Integrated process chain
01 / 06
Every casting starts with a process design. Casting simulation is used at this stage, so filling and solidification are checked before metal is poured.
02 / 06
Medium-frequency induction furnaces melt the charge. An AOD (argon oxygen decarburisation) furnace then refines it to very low carbon, phosphorus and sulphur, which is what makes super low carbon, duplex, super duplex and nickel-based steels pourable to specification.
03 / 06
The refined melt is poured into a rotating metal mould, a sand mould, or a 3D-printed sand mould. The foundry concentrates on large and highly complex stainless castings up to 15,000 kg.
04 / 06
Furnaces rated to 1,200 °C, a car-type furnace and solution pools cover the full set of treatments, so each casting is brought to its specified properties in house.
05 / 06
More than twenty machine tools take castings to rough-machined or finish-machined condition: cutting, shot blasting, horizontal and CNC lathes, CNC gantry milling, radial drilling and digital boring and milling.
06 / 06
Checks run throughout production rather than only at the end. Chemistry, mechanical properties, dimensions and internal soundness are verified against the order specification.
1.5Route selection
| Criterion | Centrifugal casting | Sand casting | PCM 3D-printed mould |
|---|---|---|---|
| Geometry | Bodies of revolution: cylinders, cones, rings | Free-form housings and rotors | Integrated complex structures and internal passages |
| Envelope | Ø up to 1,600 mm, length up to 4,200 mm; roll shells to 7,500 mm | Up to 15,000 kg per casting | Print volume 2,200 × 1,000 × 800 mm |
| Best suited to | Rotating shells where wall soundness governs | Large pressure-retaining and flow parts | New product development, small series, many variants |
| Tooling | Reusable metal moulds; more than 300 in stock | Pattern and core boxes | None: printed from digital data |
| Typical parts | Decanter bowls, roll shells, turbine casings, pipes, sleeves | Volutes, impellers, valve bodies, turbine runners | Multi-stage volutes, engine blocks and heads |
Next step
Share geometry, alloy and duty. The foundry’s engineers review every inquiry for the casting process, heat treatment, machining condition and inspection scope that fit the part.