WeizhenInternational Sales Request a quote

01Technology

Three ways to form metal. One standard for what leaves the plant.

Centrifugal casting, sand casting and patternless 3D sand printing sit under one roof with melting, AOD refining, heat treatment, machining and testing. The route is chosen for the part, and the whole chain stays under one quality system.

1.1Centrifugal casting

A seamless wall, formed by rotation.

Molten metal is poured into a spinning mould and held against the wall by centrifugal force until it solidifies. The method produces rotationally symmetric parts in one piece: bowls, shells, rings, pipes and sleeves.

  • Uniform grain structure. The wall solidifies under pressure, which improves mechanical properties around the full circumference.
  • High density. Centrifugal force removes gas bubbles and impurities from the working section.
  • Controlled wall. Rotation speed and casting duration set the wall thickness, so sizes are tailored without new tooling.
  • Forged-class performance. The manufacturer describes tensile strength and wear resistance as comparable to forged parts, at lower cost.
Machines
Horizontal and vertical centrifugal casting machines
Maximum diameter
1,600 mm
Maximum length
4,200 mm; suction roll shells up to 7,500 mm
Heavy equipment
65-tonne horizontal machine for roll shells
Mould stock
More than 300 centrifugal moulds in house
Tolerance as cast
CT9 to CT12

Source: manufacturer’s published data. The manufacturer describes its horizontal and vertical centrifugal machines as the largest in China.

Centrifugal force explorerphysics illustration

0× gravity at the mould wall

G = ω²r / g. A general physics illustration of why rotation densifies the wall. Actual casting parameters are set by the foundry for each alloy, diameter and wall section.

Horizontal

Long cylinders and shells

The mould turns about a horizontal axis on rollers. Used for cylindrical decanter bowls, pipes, tubes, liners and suction roll shells, where length exceeds diameter.

Vertical

Cones, hubs and rings

The mould turns about a vertical axis. Used for conical bowls, end hubs, casings and rings, where the profile changes along the axis or the part is short.

1.2Sand casting

Complex geometry, up to fifteen tonnes.

Where a part is not a body of revolution, it is poured in sand. The foundry concentrates on large, highly complex stainless steel castings: volutes, impellers, pulper rotors, valve bodies, turbine components and gratings.

Maximum casting weight
15,000 kg
Typical range
100 to 15,000 kg
Maximum length
4,200 mm
Tolerance as cast
CT9 to CT12
Surface as cast
Ra 12.5 to 50 µm
Alloys
Austenitic, duplex, super duplex, heat-resistant and nickel-based steels
Cope Core Casting cavity Drag

Schematic. For integrated complex structures, moulds and cores are 3D sand-printed instead of being formed around a pattern.

1.3PCM 3D sand printing

No pattern. The mould is printed from the CAD model.

Patternless Casting Manufacturing prints sand moulds and cores directly from digital data. The manufacturer was the first in China to combine it with stainless steel casting, and uses it for new product development, small series of many variants and structures a pattern could not release.

2,200 mm1,000 mm800 mm
Build envelope2,200 × 1,000 × 800 mmFour sand 3D printers

>30%

lower casting manufacturing cost

>50%

shorter production cycle

Route to the first casting

Pattern route
  1. Pattern design
  2. Pattern making
  3. Moulding and core making
  4. Pour
PCM route
  1. CAD data
  2. Print mould and cores
  3. Pour

Cost and cycle reductions are the manufacturer’s published figures for PCM compared with conventional pattern-based sand casting. Route diagram is schematic and not to scale.

1.4Integrated process chain

Six stages, one site, no hand-offs.

01 / 06

Process design and simulation

Every casting starts with a process design. Casting simulation is used at this stage, so filling and solidification are checked before metal is poured.

  • Casting simulation
  • Drawing and specification review
  • Route selection: centrifugal, sand or printed mould

1.5Route selection

Which process fits which part.

CriterionCentrifugal castingSand castingPCM 3D-printed mould
GeometryBodies of revolution: cylinders, cones, ringsFree-form housings and rotorsIntegrated complex structures and internal passages
EnvelopeØ up to 1,600 mm, length up to 4,200 mm; roll shells to 7,500 mmUp to 15,000 kg per castingPrint volume 2,200 × 1,000 × 800 mm
Best suited toRotating shells where wall soundness governsLarge pressure-retaining and flow partsNew product development, small series, many variants
ToolingReusable metal moulds; more than 300 in stockPattern and core boxesNone: printed from digital data
Typical partsDecanter bowls, roll shells, turbine casings, pipes, sleevesVolutes, impellers, valve bodies, turbine runnersMulti-stage volutes, engine blocks and heads

Next step

Send the drawing.
We return a manufacturing route.

Share geometry, alloy and duty. The foundry’s engineers review every inquiry for the casting process, heat treatment, machining condition and inspection scope that fit the part.